Gorpcore · relaxed straight, room for a mid-layer

Cotton-Sateen Field Jacket

SwitchbackField
270 GSM cotton/nylon sateen, 62 cm chest, 78 cm length, 7.5 cm stand collar, four bellows pockets with flaps, drawcord waist casing, two-way front zip under a snap storm placket
SwitchbackField — Cotton-Sateen Field Jacket (front) gorpcore cotton-sateen field jacket flat sketch template front view tech pack vector drawing drawcord waist casing 2.6, drawn released B chest 62 A length 78 drop 3 E sleeve 63
FRONT
SwitchbackField — Cotton-Sateen Field Jacket (back) gorpcore cotton-sateen field jacket flat sketch template back view tech pack vector drawing
BACK

Free vector flat

No account
The drawing above, front and back, as an editable vector — open it in Illustrator, Figma or Affinity and put your own graphics on it. Measurements aren't on the flat; they're in the tech pack.
The vector flat above is free and always will be. The tech pack — graded measurements, tolerances, fabric weights and construction — is the paid part.
Starting spec — make a sample before you order in bulk.
New to tech packs? Read how to make one, step by step →

Fabric

270
GSM · Heavyweight · range 240–310
Cotton/nylon sateen (NYCO) — 50% cotton / 50% nylon. Piece-dyed, calendered, durable water-repellent finish. Ask for the DWR to be applied after dyeing and specify it by name — a mill that quotes 'water resistant' with no finish named is quoting the base cloth
Trim: Pocket bag and facing cloth · 100% cotton twill · 130 GSM
What does GSM mean? Read the fabric weight guide →

How it's made

Shoulder
Set-in, slightly dropped shoulder, 3 cm drop — Flat-felled 1.0 cm, single-needle
Neck
Two-piece stand collar, fused, with a self-fabric inner facing; 1.2 cm twill tape across the back neck · rib height: 7.5 cm · topstitch: Single-needle 0.6 cm around the collar edge and along the attachment seam
Closure
two-way front zip, #5 moulded, under a four-snap storm placket · placket w: 4.5 cm · snaps: 4 · note: Two-way so the hem can be opened when sitting; a one-way zip on a 78 cm body rides up
Pockets
chest: Two bellows patch pockets, 13 x 14 cm, 2 cm side pleats, flapped with a snap · lower: Two bellows patch pockets, 18 x 19 cm, 2.5 cm side pleats, flapped with a snap · reinforcement: Bar-tack both top corners of every pocket and both ends of every flap; the lower pockets are the ones people put their hands in and they tear off the body panel, not the pocket
Waist
Drawcord casing through the body at 44 cm from HPS · height: 2.6 cm · cord: Flat 1.0 cm cord, ~150 cm, exits through two metal eyelets 2.2 cm either side of CF
Sleeve hem
2.5 cm turned cuff with a 1.8 cm hook-and-loop adjuster tab
Body hem
3 cm turned-up hem, chainstitched. Straight and level; the single waist cord does the shaping, so there is no hem cord. Add one only if the sample reads boxy below the waist
Side seams
Flat-felled 1.0 cm both sides
Stitch density spi
10 stitches per inch

Size chart

Garment laid flat · M is the sample size
Measure
XS
S
M
L
XL
XXL
A
Body length (HPS to hem) ± 1 cm
74
76
78
80
82
84
B
Chest width (1 cm below armhole) ± 1 cm
56
59
62
65
68
71
C
Hem width ± 1 cm
56
59
62
65
68
71
D
Across shoulder (seam to seam) ± 1 cm
50
52
54
56
58
60
E
Sleeve length (from shoulder seam) ± 1 cm
60
61.5
63
64.5
66
67.5
F
Sleeve opening (cuff, flat) ± 0.5 cm
14.5
15
15.5
16
16.5
17
G
Armhole (straight) ± 0.5 cm
28
29
30
31
32
33
O
Collar height (centre back, attachment to edge) ± 0.5 cm
7
7
7.5
8
8
8.5
W
Waist width (flat, at the casing) ± 1 cm
56
59
62
65
68
71
Make a shopper size chart from this template (PNG or Shopify) →Sample back from the factory? Check it against this tech pack →

Colourways

Olive Drab
#4A4F3A
Black
#232323
Sand
#C5B59A

Trims & notes

• #5 moulded two-way zip, 72 cm (centre front)
• Snap fasteners x4 (storm placket) + x4 (pocket flaps), 15 mm ring snap
• Metal eyelets x2 (waist casing)
• Flat drawcord 1.0 cm, ~150 cm + cord ends x2
• Hook-and-loop tape, 1.8 cm, ~24 cm (cuff tabs)
• 1.2 cm twill neck tape (~26 cm)
• Woven fusible, collar and front facings (~0.25 m2)
• Woven label (inside back neck) + care label (left side seam)
• Four bellows pockets is the whole garment, and bellows is where a factory cuts corners: a flat patch with a flap looks the same on a hanger and costs about half the labour. Specify the pleat depth (2 cm chest, 2.5 cm lower) as a measurement, not as the word 'bellows'.
• The waist casing is drawn released, at the body width, because that is how it is cut and sewn — the wearer pulls it in. Do not let a factory grade a shaped waist into the pattern from the flat; the size chart has one waist number and it is the released one.
• Specify the DWR finish and the sequence (dye, then finish). A sateen that is finished before dyeing loses most of the repellency in the dye bath, and nobody notices until the first wet sample.
• A two-way zip on a 78 cm body is not a luxury. Fixed at the hem, the jacket rides up over a mid-layer and the lower pockets end up at the wearer's ribs.
• NYCO at 270 GSM presses hard and holds a crease. Tell the factory to press the flat-felled seams with a cloth; direct iron on a 50% nylon sateen glazes the fabric and the shine does not come out.